|
Update Instructions:
Note: DO NOT unzip the service release files to your
default CAD/CAM directory.
A. Update FabriWIN:
1. To update your FabriWIN from the previous version, please click here
to get the archive files.
2. When the File Download dialog box appears, select the Save This
File to Disk option and click OK. The Save As dialog box appears.
3. Click the Save button. The Self-Extract Zip file FabriWIN11.0_11.01.exe
will be saved to the computer desktop by default.
4. Unzip the file to a temporary folder, like c:\temp.
5. Delete the following files in the default system folder of your
operating system, like C:\Windows\System32.
 DD_Root.dll
DD_ModelerGeometry.dll
DD_Gs.dll
DD_Gi.dll
DD_Ge.dll
DD_Db.dll
DD_AcisRenderer.dll
DD_AcisBuilder.dll
DD_Acis.dll
6. Copy the files the 8 DLL files in C:\temp\system32(folder created by
self extracting) to the default system folder of your operating system,
such as “C:\Windows\System32”.The 8 file names are as follows:
DD_Alloc_2.02_6.dll
DD_Db_2.02_6.dll
DD_Ge_2.02_6.dll
DD_Gi_2.02_6.dll
DD_Root_2.02_6.dll
dxfigs.dll
DxfigsWrapper.dll
ExpImpDxfDwg.dll
7. Copy the backup.bat in C:\temp\FabriWIN to the folder
C:\FabriWIN or the CAD/CAM system folder and run it.
8. Copy the other unzipped files in C:\temp\FabriWIN to the CAD/CAM system
main folder you specified before. The default folder is C:\FabriWIN.
9. Now, You have updated your CAD/CAM system. You can run it now.
B. Update Unfold3D Module
1. To Upgrade Unfold3D of FabriWIN, please click here
to get the archive files.
2. When the File Download dialog box appears, select Save this
File to disk and click OK. The Save As dialog box appears.
3. Click the Save button. The file will be saved to Desktop by default.
4. Unzip the file to a folder like C:\temp.
5. Copy backup.bat to the folder C:\Unfold3D\ FabriWIN\ and run it.
6. Copy the unzipped files/folder(s) in c:\temp\Unfold3D\ to the Unfold3D
folder you specified before. The default folder is C:\Unfold3D\ FabriWIN\.
7. Now, you have updated your Unfold3D modules. You can run it now.
C .Update Block Driver
1. To upgrade the block driver, please click here to get the driver of Sentinel
SuperPro. Driver Version 7.3.0.
2. When the File Download dialog box appears, select Save this
File to disk and click OK. The Save As dialog box appears.
3. Click the Save button. The file will be saved to Desktop by default.
4. Double click to execute the file "Sentinel Protection Installer
7.3.0.exe" you have downloaded.
5. Respond to the prompt messages and finish the installation.
6. Now, you have updated your block driver.
Enhancements:
NC Code Generation
The
system will get the Customer Data as well as Revision Data output from Part
Info, and output it to the NC Code.
Intellinest
All
sheets can have the remnant cut now, after nesting.
Tool
Now
shows tools with angle as a setting in the turret, regardless if the
setting in Tool menu is “From Turret” or “From Tool
Inventory”.
The
system will retain more tools when changing the machine file.
Other
The
maximum (“max”) microjoint that can be added in the system is
now expanded to 250.
Fixed Issues:
Customize
The
system would crash after customizing toolbars by deleting icons from
Standard toolbar.
Display
When
two punching machines were loaded one after the other, the Overtravel lines
did not refresh until Machine Info was selected and closed.
The
system should show “min dead zone” and “active station’s
dead zone” when inquiring tools and viewing sequence.
The
“convert dialog” display was too small.
The
system would show different dimensions or parts in part mode when clicking
the different part names on the part list dialog. The part and part
name on the window caption does not automatically change.
Close
pull down menus would disrupt the display.
Load File
When
loading Dxf, Iga, Dwg or Igs files, the system would ask the user to load
sheet size and material thickness.
Dxf
files loaded through the Walk-Through Wizard will have a line side problem;
the part should be processed.
Added
a switch to turn off the pop-up message for applying material and sheet
thickness.
“Apply
material thickness and sheet size” system message would appear when
loading old part, dxf file, dwg files, etc.
DXF
file output from the system would mistakenly create open entities.
Edit
When
selecting Grid, clicking on the part and then centering Grid-X to put the
part on the center of the sheet, the system moved the part to the far
right side of the sheet.
When
start point moved to the part corner, prepunch would not move with the start
point and stay in the original place.
Intellinest
Due
to an angle placement conflict, the part did not nest with the angle set in
the Part Information dialog and the parts were lost in the nesting report.
An
error message appeared when the user attempted to complete nesting jobs.
When
updating the sheet after nesting, the cutoff line on the sheet could not be
deleted or edited.
After
nesting, the tools on the part would be lost and wrong tools would be
assigned to the pattern.
Preference
Some
parameter values were multiplied 25.4 times larger when displayed in the
Tool Assignment dialog, if units converted from inches to millimeters.
NC Code Generation
When
using a special tool as a Wheel tool, the system did not pass the correct
value to the driver.
The
Cancel button, which showed up during generating NC code, did not do
anything.
The
decimal value could not be entered in the Pop-Up dialog when generating NC
code.
Generating
NC code off some sheets were excessively slow, and have been optimized.
Sequence
The
Overtravel display of this sheet did not refresh when performing View
Sequence.
System
would crash when set to auto sequence with cup and stack suction cups on
the PRUL machine.
Template Report
The
system could not print variables of the Tool conditions such as
“FeedRate 1-4” in the template report.
The
table format in the Hole Chart template should be rearranged to support one
hole in one line.
Tool
When
placing tool hits and then using “Expand All Items” to select
other tools to place, the tool hits placed were always the last one selected.
“Check
for Tool Interference” could not find the tool interference in some
parts.
Place
Special Tool Hits would have ghost image problems with drawings in black
backgrounds and white patterns.
When
turning on common tool punch, Remove DUPLICATE HITS did not remove the
Square tool double hits in this sheet.
Tool Assignment
Assigning
a special tool to the closed line, the system could hang up.
Material
When
entering the string value into some items under Edit Material\CNC Code,
pressing Enter button would change the string value into float value.
Reposition
After
clicking on Edit Reposition Amount the user was able to right click and
toggle between the repositions but when you left click nothing happened.
2D and 3D
AutoCAD
could not open .dxf files converted from .prt files, using the export
program [expgr.exe].
Under
Windows 2000 Operation System, the part could not be seen in the
Inquire/Correct window in CAD.
IMPORT/EXPORT
modules would not work correctly with Power User permissions set on NTFS
hard drive partitions.
OLE Integration
The
“Finish” button did not work under the OLE Preview dialog, when
the angle was selected.
There
would be one additional ellipse when importing this part into the system.
Part
name would appear when pressing F10 or "Save As" but the part
name would NOT be the file name box after OLE import.
Using
Open and OLE from the File menu, the user could not get the Preview for OLE
dialog.
Other
The
user could not tell which part was selected under Auto Tooling Options
Dialog.
Added
a switch to the Preferences to turn off the pop-up message for applying
material and sheet thickness.
Unable
to show all dimensions because the window was zoomed in too close.
When
outputting BMP file, the system would crash.
If
the angle was rotated in the Part Info dialog and the user switched the
view, the part would rotate off the sheet.
Area
AutoGrid function had layout conflicts.
The
pop up dialog for generating NC code would create errors for any item displayed
behind it.
When
entering Pattern Properties and other details, values would "round
up" the input data before being saved into the database, after the
user pressed OK or Tab button to accept input values.
Place
the ULX loader and the storage table at the left side by using ULXSIDE=1.
The
microjoints on this part would be lost when doing auto sequence.
The
system would crash when switching to view part mode by clicking Part
button.
When
using “import material data from FT”, an error message would
appear saying “did not install FabriTRAK.”
With
Use Subroutines and Macro On checked on, the part gird on the sheet could
not do prepierce.
UI
Changed
Part Width and Part Height into Part size X and Part size Y under the
dialog for New Part and New Sheet.
DimZ
should be changed to “other name” in the Setup Wizard.
Installation
After
the installation, the icons on the desktop would mess up.
|
